How to program a B&D remote control. Quick Guide.

Programming a B&D garage door remote for your sectional garage door opener or roller door opener is easy with this quick guide. Simply locate the model of your garage door opener from B&D and find the remote coding instructions below. 

For programming other brands, head over to the quick guide – How To Program A Garage Door Remote

B&D Controll-A-Door 4 – Remote programming.

How to program a remote control handset to a Controll-A-Door® 4 sectional door opener. 

1. Locate the square learn button on the back of the door opener. 
2. Press and hold your desired button on your handheld remote. 
3. Press and release the learn button on the back of the opener. 
4. Once you hear two clicks from the opener you can release the button on the handheld remote. 
5. To test simply press and release the button on the handheld remote. 

B&D CAD 5 – Remote programming. 

How to program a remote control to a Controll-A-Door® 5 roller door opener. 

1. In the face of the opener, press and release the Code Set button until the LED illuminates. 
2. Press and hold the button on your handheld remote control until the LED on the opener goes out then release. 
3. Press and release the button on the handheld remote to test that the process has worked. Your door will run. 

B&D Cad R – Remote programming. 

How to program a remote control to a Controll-A-Door® R roller door opener. 

1. In the face of the opener, press and release the Code Set button until the LED illuminates. 
2. Press and hold the button on your handheld remote control until the LED on the opener goes out then release. 
3. Press and release the button on the handheld remote to test that the process has worked. Your door will run. 

B&D CAD P – Remote programmingt.

How to program a remote control to a Controll-A-Door® P sectional door opener. 

1. Locate the control panel on the back of the door opener. 
2. Remove the panel cover by lifting it up from the bottom edge. 
3. Press and release the Code Set button on the control panel, an LED will illuminate. 
4. Press and release your preferred button on the handheld remote control. The LED will begin to flash. 
5. Press and release the same button on the remote again. 
6. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D CAD P DIAMOND – Remote programming. 

How to program a remote control to a Controll-A-Door® P Diamond sectional door opener. 

1. Locate the control panel on the back of the door opener. 
2. Remove the panel cover by lifting it up from the bottom edge. 
3. Press and release the Code Set button on the control panel, an LED will illuminate. 
4. Press and release your preferred button on the handheld remote control. The LED will begin to flash. 
5. Press and release the same button on the remote again. 
6. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D CAD P DIAMOND WQ – Remote programming. 

How to program a remote control to a Controll-A-Door® P Diamond WQ sectional door opener. 

1. Locate the control panel on the back of the door opener. 
2. Remove the panel cover by lifting it up from the bottom edge. 
3. Press and release the Code Set button on the control panel, an LED will illuminate. 
4. Press and release your preferred button on the handheld remote control. The LED will begin to flash. 
5. Press and release the same button on the remote again. 
6. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D CAD DIAMOND PD – Remote programming. 

How to program a remote control handset to a Controll-A-Door® Diamond PD roller door opener. 

1. Locate the control panel on the front of the roller door opener. 
2. Remove the panel cover by lifting it up from the bottom edge. 
3. Press and release the Code Set button on the control panel, an LED will illuminate. 
4. Press and hold your preferred button on the handheld remote control for two seconds.
5. Wait for 2 seconds.
6. Press and release the same button on the remote for 2 seconds. 
7. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D CAD SHED MASTER -Remote programming. 

How to program a remote control handset to a Controll-A-Door® Shed Master roller door opener. 

1. Locate the Door Code button on the underside of the opener. 
2. Press the Door Code button until the Door Code LED is illuminated then release. 
3. Press and release the desired button to be used for this door on the remote handset. 
4. The Door Code LED will go out to indicate that the remote has been learned. 

B&D Roll A Pro – Remote programming.  

How to program a remote control handset to a Roll A Pro roller door opener. 

1. Locate the control panel on the front of the roller door opener. 
2. Remove the panel cover by lifting it up from the bottom edge. 
3. Press and release the Code Set button on the control panel, an LED will illuminate. 
4. Press and hold your preferred button on the handheld remote control for two seconds.
5. Release for 2 seconds.
6. Press and release the same button on the remote for 2 seconds. 
7. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D Controll-A-Door® Smart SDO7 – Remote programming. 

How to program a remote control on a Controll-A-Door® Smart SDO7 sectional door opener. 

1. Locate the control panel on the back of the opener.
2. Press and pulse the MODE button until the Transmit LED is illuminated. 
3. Press and continually hold the DOWN button on the control panel. 
4. The Courtesy light will begin to flash. 
5. Press and hold your preferred button on the handset until the courtesy light flashes rapidly then release. 
6. Press and hold the same handset button again until the courtesy light stops flashing. 
7. Release both the DOWN button and the remote button. 
8. Press and release the MODE button to exit transmitter learn mode. 

B&D Controll-A-Door® Secure SDO6 – Remote programming. 

How to program a remote control on a Controll-A-Door® Secure SDO6 sectional door opener. 

9. Locate the control panel on the back of the opener.
10. Press and pulse the MODE button until the Transmit LED is illuminated. 
11. Press and continually hold the DOWN button on the control panel. 
12. The Courtesy light will begin to flash. 
13. Press and hold your preferred button on the handset until the courtesy light flashes rapidly then release. 
14. Press and hold the same handset button again until the courtesy light stops flashing. 
15. Release both the DOWN button and the remote button. 
16. Press and release the MODE button to exit transmitter learn mode. 

B&D Controll-A-Door® Advance – Remote programming. 

How to program a remote control to a Controll-A-Door® Advance sectional door opener.

1. Locate the control panel on the door opener and remove.  
2. Press and release the Code Set button on the control panel, an LED will illuminate. 
3. Press and release your preferred button on the handheld remote control. The LED will begin to flash. 
4. Press and release the same button on the remote again. 
5. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D Controll-A-Door® S – Remote programming. 

How to program a remote control on a Controll-A-Door® S sectional door opener. 

1. Locate the control panel on the back of the sectional door opener. 
2. Remove the panel cover by pulling it down from the top edge. 
3. Press and release the Door Code button on the control panel, the Door Code LED will illuminate. 
4. Press and hold your preferred button on the handheld remote control for two seconds.
5. Release for 2 seconds.
6. Press and release the same button on the remote for 2 seconds. 
7. The LED on the control panel will go out to indicate that the remote is programmed. 

B&D MPC1 – Remote programming.

How to program a remote control to the MPC1 roller door opener.  

1. Remove the cover from the back of the remote handset to reveal the Dip switches. 
2. Arrange the Dip switches in a random order to create your security code.
3. Replace the cover on the handheld remote.  
4. Press and release the code set button on the wall mounted control panel. 
5. Press the button on the handheld remote for 2 seconds then release. 

B&D MPC2 – Remote programming.

How to program a remote control to the MPC2 roller door opener.  

1. Remove the cover from the back of the remote handset to reveal the Dip switches. 
2. Arrange the Dip switches in a random order to create your security code.
3. Replace the cover on the handheld remote.  
4. Remove the cover from the wall mounted control panel. 
5. Press and release the code set button on the wall mounted control panel. 
6. Press the button on the handheld remote for 2 seconds then release. 

B&D MPC3 – Remote programming.

How to program a remote control to the MPC3 roller door opener.  

1. Remove the battery cover from the back of the remote handset to reveal the Dip switches. 
2. Arrange the Dip switches in a random order to create your security code.
3. Replace the cover on the handheld remote.  
4. Remove the bottom cover from the wall mounted control panel. 
5. Press and release the code set button on the wall mounted control panel. 
6. Press the button on the handheld remote for 2 seconds then release. 

B&D MPC4 – Remote programming.

How to program a remote control to the MPC4 sectional door opener.  

1. Remove the battery cover from the back of the remote handset to reveal the Dip switches. 
2. Arrange the Dip switches in a random order to create your security code.
3. Replace the cover on the handheld remote.  
4. Press and release the code set button on the back of the opener. 
5. Press the button on the handheld remote for 2 seconds then release.